Manufacturers usually represent the energy efficiency of windows in terms of their U-values (conductance of heat) or their R-values (resistance to heat flow). If a window’s R-value is high, it will lose less heat than one with a lower R-value. Conversely, if a window’s U-value is low, it will lose less heat than one with a higher U-value. In other words, U-values are the reciprocals of R-values (U-value = 1/R-value).
Usually, window R-values range from 0.9 to 3.0 (and U-values range from 1.1 to 0.3), but some highly energy-efficient exceptions also exist. When comparing different windows, you should ensure that all U-or R-values listed by manufacturers:
Today, several types of advanced glazing systems are available to help control heat loss or gain. The advanced glazings include double-and triple-pane windows with such coatings as low-emissivity (low-e), spectrally selective, heat-absorbing (tinted), or reflective; gas-filled windows; and windows incorporating combinations of these options.
Low-e glazings have special coatings that reduce heat transfer through windows. The coatings are thin, almost invisible metal oxide or semiconductor films that are placed directly on one or more surfaces of glass or on plastic films between two or more panes. The coatings typically face air spaces within windows and reduce heat flow between the panes of glass.
When applied inside a double-pane window, the low-e coating is placed on the outer surface of the inner pane of glass to reflect heat back into the living space during the heating season. This same coating will slightly reduce heat gain during the cooling season.
Low-e films are applied in either soft or hard coats. Soft-coat low-e films degrade when exposed to air and moisture, are easily damaged, and have a limited shelf life, so they are carefully applied by manufacturers in insulated multiple-pane windows. Hard low-e coatings, on the other hand, are more durable and can be used in add-on (retrofit) applications. But the energy performance of hard-coat low-e films is slightly poorer than that of soft-coat films. Windows manufactured with low-e films typically cost about 10% to 15% more than regular windows, but they reduce energy loss by as much as 30% to 50%.
Although low-e films are usually applied during manufacturing, retrofit low-e window films are also widely available for do-it-yourselfers. These films are inexpensive compared to total window replacements, last 10 to 15 years without peeling, save energy, reduce fabric fading, and increase comfort.
Spectrally selective (optical) coatings are considered to be the next generation of low-e technologies. These coatings filter out from 40% to 70% of the heat normally transmitted through clear glass, while allowing the full amount of light to be transmitted. Spectrally selective coatings can be applied on various types of tinted glass to produce “customized” glazing systems capable of either increasing or decreasing solar gains according to the aesthetic and climatic effects desired.
Computer simulations have shown that advanced glazings with spectrally selective coatings can reduce the electric space cooling requirements of new homes in hot climates by more than 40%. Because of the energy-saving potential of spectrally selective glass, some utilities now offer rebates to encourage its use.
Another technology uses heat-absorbing glazings with tinted coatings to absorb solar heat gain. Some heat, however, continues to pass through tinted windows by conduction and reradiation. But inner layers of clear glass or spectrally selective coatings can be applied with tinted glass to further reduce this heat transfer. Heat-absorbing glass reflects only a small percentage of light and therefore does not have the mirrorlike appearance of reflective glass.
Gray-and bronze-tinted windows reduce the penetration of both light and heat into buildings in equal amounts (i.e., not spectrally selective) and are the most common tint colors used. On the other hand, blue-and green-tinted windows offer greater penetration of visible light and slightly reduced heat transfer compared with other colors of tinted glass. When windows transmit less than 70% of visible light, plants inside could die or grow more slowly. In hot climates black-tinted glass should be avoided because it absorbs more light than heat.
Like black-tinted coatings, reflective coatings greatly reduce the transmission of daylight through clear glass. Although they typically block more light than heat, reflective coatings, when applied to tinted or clear glass, can also slow the transmission of heat. Reflective glazings are commonly applied in hot climates in which solar control is critical; however, the reduced cooling energy demands they achieve can be offset by the resulting need for additional electrical lighting.